Influence Surface (Highway) [SIG]

General

Influence surface coefficients are the numerical values used to determine the influence of a unit load on a specific point of a structure, based on its position and orientation. These coefficients represent the contribution of a unit load at a specific point to the total response of the structure.

Stage: During an influence surface-based live load analysis, the stiffness matrix and active elements are captured at the selected stage, followed by the placement of a unit load on the roadway surface. The analysis then determines the influence surface coefficients that are used to assess the maximum load effect on the structure.

Roadway: The roadway geometry is utilized to establish the boundaries for the unit loads that are placed at equal spacing in both longitudinal and transverse directions.

Live Load Category[Gravity/Braking/Centrifugal]: When gravity is selected, the unit loads are applied in the vertical (Z) direction. In the case of braking, the unit loads are applied 6 feet above the deck level in the longitudinal (X) direction along the alignment. For centrifugal or wind loads, the unit loads are applied in the transverse (Y) direction perpendicular to the alignment and 6 feet above the deck.

When the user selects the centrifugal option, it is important to specify the highway design speed and centrifugal force factor under the centrifugal tab. The library component will calculate the radius of curvature of the traffic lane at each unit load station based on the alignment data and automatically compute the C factor in accordance with AASHTO 3.6.3-1. The unit load (1) will then be multiplied by the C factor.

FAQ: How do we know in which direction CE/BR unit loads will be placed? Does the program automatically align and position them correctly based on the alignment?
X (longitudinal) and Y (centrifugal) are in the alignment coordinate system. Each unit load is placed with respect to the direction of the curve at that specific location. You can view all unit loads by selecting the 'Loading' mode and the influence surface you are interested in. Note that these loads are individually defined in the global coordinate system, while the combined load is perpendicular to the PGL. Below is an example of a centrifugal load unit load, which applies the load perpendicular to the PGL and directs it outward from the curve.

Unit Load Spacing Long. : The spacing of the unit loads in both longitudinal and transverse directions significantly affects the total analysis time. For each unit load, a finite element analysis must be conducted. For instance, if we consider a roadway that is 1000 feet in the longitudinal direction and 50 feet in the transverse direction, using a spacing of 1 foot in both directions would require 50,000 finite element analysis runs. Additionally, identifying the critical vehicle positions using these runs would also be a time-consuming task. For this reason, when considering the longitudinal direction, it is recommended to use a spacing value of 10 feet or the span length divided by 20 or 10 as it provides a good approximation.

Unit Load Spacing Trans.: A good approximation for transverse spacing can be achieved by starting with a vehicle width of 6 feet and gradually reducing it to 3 feet in subsequent runs.

To ensure that the model runs without any issues, it is convenient and faster to start with larger numbers for both longitudinal and transverse unit load spacing. For instance, using 20 feet in the longitudinal direction and 10 feet in the transverse direction can be a good starting point. Once you have confirmed that the model runs smoothly and have reviewed the design report, you can proceed with a spacing value of 10 feet in the longitudinal direction and 6 feet in the transverse direction to check your design. After finalizing your design, it is recommended to perform another check using a spacing of 5-10 feet in the longitudinal direction and 3 feet in the transverse direction.

Direction[Along PGL/Orthogonal to PGL]:

Placement of unit loads onto the roadway should be along the PGL in most cases. This approach covers some unique situations where the traffic direction is not along the PGL but orthogonal to the roadway

Centrifugal

Highway Design Speed: Highway design speed shall not be taken to be less than the value specified in the current edition of the AASHTO. 1.0 ft/s = 0.682 mph

Centrifugal Force Factor: 4/3 for load combinations other than fatigue and 1.0 for fatigue

Braking

Braking Force Direction [Bidirectional/One Direction]: The direction of the braking force applied at the nodes of the structure can be defined using this parameter. Users can specify whether to apply the braking loads in a single direction or in two directions.

Settings

Coeff. Tol.: