...
Step 1: Adding Sections to the Project
| 1 | Navigate to Properties > Sections |  |
| 2 | To import a section, click on the three-dot icon located on the first cell of the Name and select "Import Section". | |
| 3 | Select OpenBrIM Bridge Objects > Precast I Girder Sections > |
AASHTO I BEAMS > AASHTO_TYPE_III_BEAM Assign Material as: Fc_6ksi |  | |
| 4 | Select OpenBrIM Bridge Objects > Basic Sections > Basic Shapes > Circle | 
|
| 5 | Enter Radius as 18 in import section editor. | |
| 6 | Click Import | |
| 7 | Assign Material as Fc_4ksi (If the material Fc_4ksi is already assigned by default, there is no need to assign it again) | |
| 8 | Rename this section as Circle_exist_shaft_EB | |
| 9 | Repeat the same steps from |
4 to |
8 for the other basic section.
Rename this section as Circle_exist_shaft_Pier Assign Material as Fc_4ksi |  |
| 10 | Repeat the same steps from |
4 to |
8 for the other basic section.
Rename this section as Circle_exist_column Assign Material as Fc_5_1/2ksi |  |
| 11 | Repeat the same steps from |
4 to |
8 for the other basic section. Enter Witdh and Depth
Rename this section as Rectangle_exist_EBcap Assign Material as Fc_5_1/2ksi |  |
| 12 | Repeat the same steps from |
4 to |
8 for the other basic section. Enter Witdh and Depth
Rename this section as PierCap_exist Assign Material as Fc_5_1/2ksi |  | |||||
| 13 | Select OpenBrIM Bridge Objects > Barrier Sections > General > SingleSlopeRight Enter Bottom & Top Witdh and Depth
Rename this section as Exist_Barrier_sw Assign Material as Fc_3_2ksi_NoStiffness | 
| ||||
| 14 | To access section editor click on the relevant cell in the "Name" column and select it from the combobox. | |||||
| 15 | Click on the blue circular box that appears after clicking the section shape, and Click Points Spreadsheet from the combobox. Copy the data below.
Paste copied data. | |||||
| 16 | Create a new section by defining its name as RigidSection |
| ||||
| 17 | Copy and pastethe data below.
Refer to following page for more information about how to define Rigid Section |
| Tip |
|---|
Completed Sections definitions are illustrated below. |
...
| Info |
|---|
Please follow the instructions provided below to set rebar and tendon detailing for AASHTO_TYPE_III_BEAM |
From any cell of the AASHTO_TYPE_III_BEAM row, click on three-dots icon to open Section Editor panel. |  |
Click + icon at the left top side of the screen. And Select Rebar | |
Enter:
Click Add. |  |
Enter:
Click Add. |  |
Click + icon at the left top side of the screen. And Select Tendon |  |
Enter:
|
Click Add. | 
|
Enter:
Click Add. | |
Enter:
|
|
|
|
Click Add. |
...
| Info |
|---|
Please follow the instructions provided below to set rebar detailing for Circle_exist_column |
From any cell of the Circle_exist_column row, click on three-dots icon to open Section Editor panel. |  |
Click + icon at the left top side of the screen. And Select Rebar | |
Navigate to the "Circular Layout" tab Enter:
Click Add. |  |
 |
...
| Info |
|---|
Please follow the instructions provided below to set rebar detailing for Rectangle_exist_EBcap |
From any cell of the Rectangle_exist_EBcap row, click on three-dots icon to open Section Editor panel. |  | |||||
Click + icon at the left top side of the screen. And Select Rebar | ||||||
Navigate to the "Draw Rebar Points" tab Enter:
Click Add. Manually top position the rebar line within the section. And set data as follows:
Click Apply. | 
| |||||
Click … icon shown on created rebar. Click Points Spreadsheet. Copy the data below.
|  | |||||
Repeat the previous steps to define the Rebar into the Section |
| |||||
Select Rebar
Click Add. Manually middle position the rebar line within the section. And set data as follows:
Click Apply. | ||||||
Click … icon shown on created rebar. Click Points Spreadsheet. Copy the data below.
|  | |||||
Select Rebar Enter:
Click Add. Manually bottom position the rebar line within the section. And set data as follows:
Click Apply. |
| |||||
Click … icon shown on created rebar. Click Points Spreadsheet. Copy the data below.
|  |
...
| Info |
|---|
Please follow the instructions provided below to set rebar detailing for PierCap_exist |
From any cell of the PierCap_exist row, click on three-dots icon to open Section Editor panel. |  | ||||
Click + icon at the left top side of the screen. And Select Rebar | |||||
Navigate to the "Draw Rebar Points" tab Enter:
Click Add. Manually top position the rebar line within the section. And set data as follows:
Click Apply. |
| ||||
Click … icon shown on created rebar. Click Points Spreadsheet. Copy the data below.
| |||||
Navigate to the "Draw Rebar Points" tab Enter:
Click Add. Manually bottom position the rebar line within the section. And set data as follows:
Click Apply. |
| ||||
Click … icon shown on created rebar. Click Points Spreadsheet. Copy the data below.
| |||||
Select Rebar
Click Add. Manually middle position the rebar line within the section. And set data as follows:
Click Apply. | 
| ||||
Click … icon shown on created rebar. Click Points Spreadsheet. Copy the data below.
|
...