Versions Compared

Version Old Version 4 New Version 5
Changes made by

Cagin Yakar

mert.goktas

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Navigate to Bridge Geometry > Insertion Point

Click the three-dots on the first cell of the Location and create the first insertion point by setting its location to Abut1

Each bearing must have a minimum of one insertion point. Additionally, for each precast girder, there should be one insertion point at the beginning and one at the end.


Since there are five girders from Abut1 support line to Pier1 support line, we need to define five insertion points at Abut1.


To position the insertion point on the support line, input the Transverse Offset and Longitudinal Offset values as shown in the figure.

Image RemovedImage Added

Repeat the same to create other insertion points and set their transverse offset values

Image RemovedImage Added
Expand
titleQuick Tip: Skew angle & Offset parameter calculation

Skew angle and transverse offset parameters for support lines that have skew > 0. User need to enter T value for skewed supports.

Skew angle and longitudinal offset parameters for support lines that have skew > 0.

...

1

Navigate to Insertion Point under Bridge Geometry.

2

Copy Bridge Parameters from model inputs and paste into OpenBrIM.

...

Tip

Insertion point layout is given below.

...

Insertion Point

Bridge Parameters

Code Block
languagexml
IP1	Abut1	01.91860000	-1011.95440000
IP2	Abut1	01.91860000	-3.25795000
IP3	Abut1	01.91860000	4.43875000
IP4	Abut1	01.91860000	12.13520000
IP5	Abut1	01.91860000	1920.83180000
IP6	Pier1	-01.91860000	-1011.9380000
IP7	Pier1	-01.91860000	-3.24155000
IP8	Pier1	-01.91860000	4.45515000
IP9	Pier1	-01.91860000	12.15160000
IP10	Pier1	-01.91860000	1920.84820000
IP11	Pier1	01.91860000	-1011.92750000
IP12	Pier1	01.91860000	-56.79840000
IP13	Pier1	01.91860000	-01.66930000
IP14	Pier1	01.91860000	4.45515000
IP15	Pier1	01.91860000	910.58890000
IP16	Pier1	01.91860000	1415.7180000
IP17	Pier1	01.91860000	1920.84720000
IP18	Pier2	-01.91860000	-11.0760000
IP19	Pier2	-01.91860000	-56.94950000
IP20	Pier2	-01.91860000	-01.82040000
IP21	Pier2	-01.91860000	4.30875000
IP22	Pier2	-01.91860000	910.43780000
IP23	Pier2	-01.91860000	1415.56690000
IP24	Pier2	-01.91860000	1920.69590000
IP25	Pier2	01.91860000	-11.050000
IP26	Pier2	01.91860000	-3.36295000
IP27	Pier2	01.91860000	4.32435000
IP28	Pier2	01.91860000	12.01140000
IP29	Pier2	01.91860000	1920.69850000
IP30	Abut2	-01.91860000	-1011.7510000
IP31	Abut2	-01.91860000	-3.0640000
IP32	Abut2	-01.91860000	45.62250000
IP33	Abut2	-01.91860000	12.30955000
IP34	Abut2	-01.91860000	1920.99660000