Versions Compared

Version Old Version 1 New Version 2
Changes made by

mert.goktas (Unlicensed)

mert.goktas (Unlicensed)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Info

Please follow the instructions provided below to add the insertion points where the bearings will be created.

Navigate to Bridge Geometry > Insertion Point

Image Added

Click the three-dots on the first cell of the Location and create the first insertion point by setting its location to Abut1

Precast girders have a starting and ending point. These points need to be determined along the road route.
There should be as many insertion points as there are girders from each support line to the other support line.
Additionally, an insertion point can be the beginning of one entry and the end of another, so it can be used jointly or not.
Since there are five girders from Abut1 support line to Pier1 support line, we need to define five insertion points.

Enter Transverse Offset and Longitudinal Offset as in the figure to relocate the insertion point on the support line

Image Added

Image Added

Repeat the same to create other insertion points and set their transverse offset values

Image Added

Expand
titleQuick Tip: Skew angle & Offset parameter calculation

Skew angle and transverse offset parameters for support lines that have skew > 0. User need to enter T value for skewed supports.

Image Added

Skew angle and longitudinal offset parameters for support lines that have skew > 0.

Image Added

Insert excerpt
_ConfluenceInclusions
_ConfluenceInclusions
nameTubGirderPGL
nopaneltrue

...

Insert excerpt
_ConfluenceInclusions
_ConfluenceInclusions
nameCopyPaste
nopaneltrue

1

Navigate to Insertion Point under Bridge Geometry.

2

Copy Bridge Parameters from model inputs and paste into OpenBrIM.

...

Tip

Insertion point layout is given below.

...

Insert excerpt
_ConfluenceInclusions
_ConfluenceInclusions
namePasteTip
nopaneltrue

Anchor
ModelInputs
ModelInputs

Code Block
languagexml
IP1	Abut1	0.9186	-10.9544
IP2	Abut1	0.9186	-3.2579
IP3	Abut1	0.9186	4.4387
IP4	Abut1	0.9186	12.1352
IP5	Abut1	0.9186	19.8318
IP6	Pier1	-0.9186	-10.938
IP7	Pier1	-0.9186	-3.2415
IP8	Pier1	-0.9186	4.4551
IP9	Pier1	-0.9186	12.1516
IP10	Pier1	-0.9186	19.8482
IP11	Pier1	0.9186	-10.9275
IP12	Pier1	0.9186	-5.7984
IP13	Pier1	0.9186	-0.6693
IP14	Pier1	0.9186	4.4551
IP15	Pier1	0.9186	9.5889
IP16	Pier1	0.9186	14.718
IP17	Pier1	0.9186	19.8472
IP18	Pier2	-0.9186	-11.076
IP19	Pier2	-0.9186	-5.9495
IP20	Pier2	-0.9186	-0.8204
IP21	Pier2	-0.9186	4.3087
IP22	Pier2	-0.9186	9.4378
IP23	Pier2	-0.9186	14.5669
IP24	Pier2	-0.9186	19.6959
IP25	Pier2	0.9186	-11.05
IP26	Pier2	0.9186	-3.3629
IP27	Pier2	0.9186	4.3243
IP28	Pier2	0.9186	12.0114
IP29	Pier2	0.9186	19.6985
IP30	Abut2	-0.9186	-10.751
IP31	Abut2	-0.9186	-3.064
IP32	Abut2	-0.9186	4.6225
IP33	Abut2	-0.9186	12.3095
IP34	Abut2	-0.9186	19.9966