Versions Compared

Version Old Version 8 New Version Current
Changes made by

Dogukan Kilic

Dogukan Kilic

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: draw.io diagram "Girder Strand" edited
Excerpt
nameGirder Strand

3D Reference

Pretensioning strands generally applied to the precast segments. In OpenBrIM, to specify the segments creating a Support Line to specify the start and end portions of the segments is beneficial for defining inputs.

Girder: Select the girder that strands are applied. Pretension loads are distributed to the this structurestructural element.

Start Support Line: Starting support line for the precast segment.

Offset From Start Support/Insertion Point [ft]: Set the longitudinal offset from the Start Support Line, if applicable.

End Support Line: End support line for the precast segment.

Offset from End Support/Insertion Point [ft]: Set the longitudinal offset from the End Support Line, if applicable.

Strand Row Data: To view the inputs, click the three-dot menu, then select "Edit…". The description of the inputs is listed below.

Strand Data

 

Type

Specify the type of the strand Straight or Harped.

Inner strand spacing[in]

Select a reference support line.

Horizontal spacing between strands[in]

Set the station difference along PGL from Reference Support Line.

# of Strands

Set the transverse offset according to Section Reference Edge of Girder.

Reference Edge

Set the vertical offset according to Section Reference Edge of Girder.

Distance to Reference Edge [in]

Set the point’s radius of curveSpecify the inner strand spacing. The distance is measured from the center of one strand to the center of the another strand.

Outer Strand Spacing[in]

Specify the outer strand spacing between strands. The distance is measured from the center of one strand to the center of the adjacent strand.

Horizontal Offset from Center[in]

Specify the horizontal offset to move center of the strand row.

# of Strands

Specify the number of strands in a single row.

Reference Edge

Specify the reference edge for Distance to Reference Edge input.

Distance to Reference Edge @ Start[in]

Set the distance to reference edge. This distance is measured from the Reference Edge of the section to the center of the strand. Only avaliable when strand Type is Harped.

Harped Distance[ft]

Distance of the harped location from the start

Distance to Reference Edge @Harped Dist. [in]

Set the distance to reference edge. This distance is measured from the Reference Edge of the section to the center of the strand. Only avaliable when strand Type is Harped.

Debonding Length (Start)[in]

Specify the debonding length of at the Start of the stra.

Debonding Length (End)[in]

Specify the debonding length at the End of the strands.

Drawio sketch
mVer2
simple0
zoom1
inComment0
pageId2226389020
custContentId2241101946
diagramDisplayNameGirder Strand
lbox1
contentVer23
revision23
baseUrlhttps://openbrim.atlassian.net/wiki
diagramNameGirder Strand
pCenter0
width1231
links
tbstyle
height737.53
Drawio sketch
mVer2
simple0
zoom1
inComment0
pageId2226389020
custContentId2349694995
diagramDisplayNameHarpedStrand
lbox1
contentVer1
revision1
baseUrlhttps://openbrim.atlassian.net/wiki
diagramNameHarpedStrand
pCenter0
width6121331.00000000000019999999999998
links
tbstyle
height731445.560000000000108000000000004

Properties

Material: Set the material for the strand.

Wobble Friction Coefficient [1/ft]: Pretensioning applications doesn’t include frictional losses that’s why this parameter has default zero value.

Curvature Friction Coefficient (1/rad): Pretensioning applications doesn’t include frictional losses that’s why this parameter has default zero value.

Jacking

Strand Type: Enter the strand type for the tendon. The strand type can be imported from the Properties section.

Jacking Method[Start/End/Start then End/ End then Start]: Specify the jacking method that is applied to the tendon. In the case of Girder Strand, start and end refer to downstation and upstation directions with respect to PGL.

Jacking Force From Start [kip]: Enter the start jacking force that is applied to the tendon. It must be specified, unless Jacking Method is selected End.

Jacking Force From End [kip]: End jacking force that is applied to the tendon. It must be specified, unless Jacking Method is selected Start.

FEA Settings

Load Dist. Elem. Type[FENodes/FELines]: This input affects the type of finite elements loads are distributed. FELines are used for beam elements.

Percent Loss(%): Set the percent loss for the long-term losses. This is an optional input. Users can leave this input as 0 and let OpenBrIM calculate the long-term losses using the CEB-FIB 1990 curve by running the time-dependent analysis. Alternatively, users can set an approximate value for the Percent Loss (%) to account for long-term losses, which will reduce the Jacking Force values of the tendon.