| Info |
|---|
After clicking on 'Properties>Sections' in the navigation treeview, follow the steps to define the Sections. You can use the collapsed documentation page below for more information on the explanations of each parameter. |
...
| 1 | Go to Properties > Sections |  |
| 2 |  Click the three-dots on the first cell of the Name and click Import Section
|
| 3 |  Select OpenBrIM Bridge Objects > Basic Sections > Basic Shapes > Rectangle
| 
|
| 4 |  Enter both Witdh and Depth as 96 in
|
| 5 |  Click Import
|
| 6 |  Rename this section as PierCapRec_Mid
|
| 7 |  Assign Material as Fc_4ksi
|
| 8 |  Repeat the same steps from 2 to 7 for the second rectangular section
 Enter Witdh and Depth
 Rename this section as PierCapRec_Taper
 Assign Material as Fc_4ksi
|
| 9 |  Repeat the same steps from 2 to 7 for the third rectangular section
 Enter Witdh and Depth
 Rename this section as PierColumnRec
 Assign Material as: Fc_4ksi
|
| 10 |  Repeat the same steps from 2 to 7 to import a circular section
 Enter radius: 21
 Rename This section as PierColumnCircle
 Assign Material as Fc_4ksi
| 
|
| 11 |  Repeat the same steps from 2 to 7 to import the second circular section
 Enter radius: 20
 Rename This section as PileCircle
 Assign Material as Fc_4ksi
|
| 12 |  Import another section by selecting OpenBrIM Bridge Objects > AISC Steel Shape Database > L Type > AISCL8X8X3/4
Assign Material as A709_50 |  |
| 13 |  Copy and pastethe data below.
| Code Block |
|---|
RigidSection RigidMaterial 6400.0000 6400.0000 6400.0000 3413333.3333 3413333.3333 3413333.3333 0.0000 YES NO NO NO |
| 
|
| 14 | Import the last section from OpenBrIM Bridge Objects > Barrier Sections > F Shape Barrier> F Shape Assign Material as FcCube_NoStiffness |  Image Removed Image Added
|
| Tip |
|---|
Completed Sections definitions are illustrated below. |
...
| 1 | For any section, it is possible to add or change parameters that are used in geometry definitions. Click on three-dots icon to open Parameters tab. |  |
| 2 | In this menu, you can change the value of the parameter or add a new one to be used in the Section Editor. |  |
| 3 | These parameters can be utilized in the Section Editor → Points Spreadsheet, which is explained in the subsequent sections. | |
Properties >
| Info |
|---|
Follow the next steps to set rebar detailing for PierCapRec_Mid. |
| 1 | From any column of the PierCapRec_Mid row, click on three-dots icon to open Section Editor panel. |  |
| 2 | Click + icon at the left top side of the screen. |  |
| 3 | Select Rebar. Enter: Click Add. |  Image Removed Image Added
|
| 4 | Click two different points within the shape. |  Image Removed Image Added
|
| 5 | From the opening tab select: Profile: ASTMA615No9 Material: A615_60 Keep # of Rebars (per Row) as 14. Click Apply. |  Image Removed Image Added
|
| 6 | Click … icon shown on top right edge of rebars. |  |
| 7 | Click Unlock Movement. Then repeat step 6 and click Points Spreadsheet. |  |
| 8 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
-45.0000 45.0000
45.0000 45.0000 |
| 
|
| 9 | Paste copied data. |
| 10 | Click + icon at the left top side of the screen. |  Image Removed
 Image Added
 Image Added
 Image Added
Image Added |
| 11 | Select Rebar. Enter: Click Add. |
| 12 | Click two different points within the shape. |
| 13 | From the opening tab select: Profile: ASTMA615No8 Material: A615_60 Keep # of Rebars (per Row) as 9. Click Apply. |
| 14 | Click … icon shown on top right edge of rebars. |
| 15 | Click Unlock Movement. Then repeat step 14 and click Points Spreadsheet. |
| 16 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
-41.7500 -41.7500
41.7500 -41.7500 |
|
| 17 | Paste copied data. |
| Info |
|---|
Follow the next steps to set rebar detailing for PierCapRec_Taper. |
...
Image Removed From any column of the PierCapRec_Taper row, click on three-dots icon to open Section Editor panel
...
...
Image Removed Click + icon at the top left side of the window
...
...
Image Removed Select Rebar
...
...
Image Removed Enter the following data and click Add
...
...
Image Removed Click two different points within the shape.
...
| Panel |
|---|
| panelIconId | atlassian-check_mark |
|---|
| panelIcon | :check_mark: |
|---|
| panelIconText | :check_mark: |
|---|
| bgColor | #E3FCEF |
|---|
|
To see an example of rebar definition for a section, you can refer to the video below. The PierCapRec_Mid rebar definition is included. |
...
| Info |
|---|
Follow the next steps to set rebar detailing for PierCapRec_Taper. |
| 1 | Image Added From any column of the PierCapRec_Taper row, click on three-dots icon to open Section Editor panel |  Image Added |
| 2 | Image Added Click + icon at the top left side of the window |  Image Added |
| 3 | Image Added Select Rebar |  Image Added |
| 4 | Image Added Enter the following data and click Add |  Image Added
|
| 5 | Image Added Click two different points within the shape. | Image Added |
| 6 | Image Added Select the following data and click Apply Profile: ASTMA615No9 Material: A615_60  Image RemovedKeep # of Rebars (per Row) as 2. |  Image Added
|
| 7 | Click three-dotsicon on the top right edge of rebars | Image Removed  Image Added
|
| 8 | Click Unlock Movement. Then repeat step 7 and click Points Spreadsheet. | Image Removed  Image Added
|
| 9 | Copy and pastethe data below. | Code Block |
|---|
0.0000 0.0000
-41.6220 20.0000
-39.3720 20.0000 |
|
|
| 10 | Repeat Steps 2-7 by using data below. 2 | Code Block |
|---|
0.0000 0.0000
-25.8680 20.0000
-28.1240 20.0000 |
3 | Code Block |
|---|
0.0000 0.0000
-12.3700 20.0000
-14.6260 20.0000 |
4 | Code Block |
|---|
0.0000 0.0000
-1.1280 20.0000
1.1280 20.0000 |
5 | Code Block |
|---|
0.0000 0.0000
12.3700 20.0000
14.6260 20.0000 |
6 | Code Block |
|---|
0.0000 0.0000
25.8680 20.0000
28.1240 20.0000 |
7 | Code Block |
|---|
0.0000 0.0000
41.6220 20.0000
39.3720 20.0000 |
|  Image Removed Image Added
|
| 11 | Click + icon at the left top side of the screen. | 
|
| 12 | Select Rebar. Enter: Click Click Add. |
| 13 | Click two different points within the shape. |
| 14 | From the opening tab select: Profile: ASTMA615No8 Material: A615_60 Click Apply. |
| 15 | Click … icon shown on top right edge of rebars. |
| 16 | Click Unlock Movement. Then repeat step 15 and click Points Spreadsheet. |
| 17 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
-41.7500 -20.0000
41.7500 -20.0000 |
|
| 18 | Paste copied data. |
| Info |
|---|
Follow the next steps to set rebar detailing for PierColumnRec. |
| 1 | From any column of the PierColumnRec row, click on three-dots icon to open Section Editor panel. | |
| 2 | Click + icon at the left top side of the screen. | |
| 3 | Select Rebar. Enter: Click Add. |  Image Removed Image Added
|
| 4 | Click two different points within the shape. | |
| 5 | From the opening tab Select: Profile: ASTMA615No9 Material: A615_60 Keep # of Rebars (per Row) as 10. Click Apply. |  Image Removed Image Added
|
| 6 | Click … icon shown on top right edge of rebars. | |
| 7 | Click Unlock Movement. Then repeat step 6 and click Points Spreadsheet. | |
| 8 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
-35.0000 35.0000
35.0000 35.0000 |
|
|
| 9 | Paste copied data. |
| 10 | Click + icon at the left top side of the screen. |
|
| 11 | Select Rebar. Enter: Click Add. |
| 12 | Click two different points within the shape. |
| 13 | From the opening tab Select: Profile: ASTMA615No9 Material: A615_60 Keep # of Rebars (per Row) as 10. Click Apply. |
| 14 | Click … icon shown on top right edge of rebars. |
| 15 | Click Unlock Movement. Then repeat step 14 and click Points Spreadsheet. |
| 16 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
-35.0000 -35.0000
35.0000 -35.0000 |
|
| 17 | Paste copied data. |
| 18 | Click + icon at the left top side of the screen. | 
|
| 19 | Select Rebar. Enter: Click Add. |
| 20 | Click two different points within the shape. |
| 21 | From the opening tab Select: Profile: ASTMA615No9 Material: A615_60 Click ApplyKeep # of Rebars (per Row) as 7. Click Apply. |
| 22 | Click … icon shown on top right edge of rebars. |
| 23 | Click Unlock Movement. Then repeat step 22 and click Points Spreadsheet. |
| 24 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
-35.0000 27.3780
-35.0000 -27.3780 |
|
| 25 | Paste copied data. |
| 26 | Click + icon at the left top side of the screen. |
| 27 | Select Rebar. Enter: Click Add. |
| 28 | Click two different points within the shape. |
| 29 | From the opening tab Select: Profile: ASTMA615No9 Material: A615_60 Keep # of Rebars (per Row) as 7. Click Apply. |
| 30 | Click … icon shown on top right edge of rebars. |
| 31 | Click Unlock Movement. Then repeat step 30 and click Points Spreadsheet. |
| 32 | Copy the data below. | Code Block |
|---|
0.0000 0.0000
35.0000 27.3780
35.0000 -27.3780 |
|
| 33 | Paste copied data. |
...
| Expand |
|---|
|
| Panel |
|---|
| panelIconId | atlassian-info |
|---|
| panelIcon | :info: |
|---|
| bgColor | #DEEBFF |
|---|
| Follow the next steps to create different section definitions that OpenBrIM provides. |
| 1 | Enter a Section under Name. |   | | 2 | Import a material. | | 3 | From any column of the added row, click on three-dots icon to open Section Editor panel. |  | | 4 | You can open the tab which includes Polygon, Template, Rebar and Tendon by clicking Shapes icon at the left top side of the screen. |  | | 5 | To define a polygon shape, click to Polygon at Shapes tab, then click the coordinates of an arbitrary shape. | -20221006-141301.png?version=1&modificationDate=1665065590914&cacheVersion=1&api=v2) | | 6 | | Expand |
|---|
| You can rechange the locations by clicking ‘Points Spreadsheet’ after you assign the shape.  |
| | 7 | To utilize a Template click Template. | -20221006-142008.png?version=1&modificationDate=1665066020200&cacheVersion=1&api=v2) | | 8 | If you don’t have a material already imported (or defined as custom), you can import by clicking Import. If you have, just select it from the Material drop-down. | -20221006-142433.png?version=1&modificationDate=1665066281224&cacheVersion=1&api=v2) | | 9 | Edit dimensions of the shape to create the section. Click to Import. | -20221006-142448.png?version=1&modificationDate=1665066296420&cacheVersion=1&api=v2) | | 10 | After you import the section, it will show up on the section editor. |  | | 11 | To add rebars to your section click Rebar at the Shapes tab. | -20221006-142614.png?version=1&modificationDate=1665066381455&cacheVersion=1&api=v2) | | 12 | If you don’t have a Rebar definition in your project, you will get a popup to import one. Just click OK and continue. |  | | 13 | Select your asset from OpenBrIM Database for rebar profile and click Import. |  
| | 14 | By clicking Line Layout, you can switch the layout of the rebar as Line, or Circular. | -20221006-143057.png?version=1&modificationDate=1665066665741&cacheVersion=1&api=v2) | | 15 | Let’s stay on Line Layout, and enter rebar layout input data. | | 16 | After you click Add, you should click the start and end location points of the section. No need to be exact in locations, they can be edited later. | -20221006-145238.png?version=2&modificationDate=1665067995346&cacheVersion=1&api=v2) | | 17 | After clicking end location, Edit Linear Rebar Layout window appears. | -20221006-145456.png?version=1&modificationDate=1665068115619&cacheVersion=1&api=v2) | | 18 | Edit Linear Rebar Layout. | -20221006-145651.png?version=1&modificationDate=1665068230049&cacheVersion=1&api=v2) | | 19 | If you don’t have a rebar material already imported (or defined as custom), you can import by clicking Import . If you have, just select it from the Material drop-down. |  Image Removed | | 20 | After Apply all the entered data in Edit Linear/Circular Rebar Layout window, you can change the location of the rebar layout at the analytical coordinate system by clicking Points Spreadsheet under three-dots. | -20221006-145837.png?version=1&modificationDate=1665068328109&cacheVersion=1&api=v2) Image Removed | | 21 | Applying the same procedure, you can insert rebars at top and bottom. This time number of rows is set to 1 and rebar layouts placed twice for top and bottom, respectively. |  Image Removed Image Removed | | 22 | | Expand |
|---|
| The rebars are completed. This training example doesn’t require any tendon definition; the below steps explain how to add a tendon layout to the section. |
| | 23 | To add tendon to your section click Tendon at the Shapes tab. | -20221006-150314.png?version=2&modificationDate=1665068607108&cacheVersion=1&api=v2) Image Removed | | 24 | After you import the material for the tendon and add the tendon to your section, you can rearrange the coordinates of the tendon. | -20221006-150521.png?version=1&modificationDate=1665068728526&cacheVersion=1&api=v2) Image Removed | | 25 | Also, you can use a parametric relationship as input for Y1=d/2-10 (d = depth of the section). The position of the rebar depends on the section depth. |  Image Removed |
|
| Panel |
|---|
| panelIconId | atlassian-check_mark |
|---|
| panelIcon | :check_mark: |
|---|
| panelIconText | :check_mark: |
|---|
| bgColor | #E3FCEF |
|---|
|
To see an example of rebar definition for a section, you can refer to the video below. The PierCapRec_Mid rebar definition is included. |
...
from the Material drop-down. | Image Added | | 20 | After Apply all the entered data in Edit Linear/Circular Rebar Layout window, you can change the location of the rebar layout at the analytical coordinate system by clicking Points Spreadsheet under three-dots. | Image Added | | 21 | Applying the same procedure, you can insert rebars at top and bottom. This time number of rows is set to 1 and rebar layouts placed twice for top and bottom, respectively. | Image AddedImage Added | | 22 | | Expand |
|---|
| The rebars are completed. This training example doesn’t require any tendon definition; the below steps explain how to add a tendon layout to the section. |
| | 23 | To add tendon to your section click Tendon at the Shapes tab. | Image Added | | 24 | After you import the material for the tendon and add the tendon to your section, you can rearrange the coordinates of the tendon. | Image Added | | 25 | Also, you can use a parametric relationship as input for Y1=d/2-10 (d = depth of the section). The position of the rebar depends on the section depth. | Image Added |
|