...
Slab reinforcement design of the 1st floor will be performed in this section.
General
General setting are found in this spreadsheet for slab design
...
Figure 1
Click “Design Strip” button as User can edit the slab and column intensity factor and column reinforcement coun rectangle factor as shown in Figure 1 to draw directions for layers. When direction1 is drawn direction2 which is perpendicular to it will be drawn automatically as illustrated in Figure 2. These directions are assigned to layers by default but can be edited later as demonstrated in Figure 3.
| Show if | ||
|---|---|---|
| ||
Figure 1’deki Design Strip butonuna tıklanarak Figure 2’deki gibi direction1 çizilir ve otomatik olarak direction1’e dik olan direction2 oluşur. Bu yönler default olarak Figure 3’deki gibi layer’lere atanır ancak kullanıcı isterse değiştirebilir. |
...
Figure 2
...
Figure 3
Click “Shear Wall Coner Zones” at spreadsheet as in Figure 1.
Click “Generate Corner Zones” button as in Figure 4 .
...
Corner Zones
There must be column or shear wall at both ends of the stress lines to ensure the boundary conditions at ends.
There must be corner zones on shear walls where the stress lines will be generated.
...
Figure 2
→ Click Generate Corner Zones button as in Figure 2 to generate zones in shear walls for generation of stresslines .
→ Click “Draw Draw Corner Zone” Zone button as shown in Figure 4 2 to create draw the zones manually for stressline generation.
| Show if | ||
|---|---|---|
| ||
Figure 3’deki parametre ve değerler kullanıcı tarafından değiştirilebilir. Figure 1’de Spreadsheet data butonuna tıklanarak Shearwall Corner Zone seçildiğinde; |
...
Figure 4
| Show if | ||
|---|---|---|
| ||
Figure 4’deki Generate Corner Zone butonuna tıklanarak perde duvar köşelerinde stressline üretilmesi için BDS tarafından noktalar oluşturulur. Bu noktalar Draw Corner Zone butonuna tıklandığında kullanıcı tarafından da oluşturulabilir. Corner zone oluşturulduktan sonra Run Stress Line Generation butonuna tıklandığında BDS tarafından stressline’ler üretilir. Figure 1’de Spreadsheet data butonuna tıklanarak Stress Lines seçildiğinde; |
Click “Stress Lines” at spreadsheet as in Figure 1.
Click “Run Stress Line Generation” button as in Figure 4 or Figure 5 to generate stress lines on slab.
...
Figure 5
Click “Draw Stress Line” button as in Figure 5 to draw stress lines manually. Edges of stress lines must be on columns or corner zones of shear walls.
Generated stress lines can be deleted if not necessary.
...
| userGroups | Turkish |
|---|
...
User can delete the corner zones in two ways;
→ Right click the corner zone in the spreadsheet and click delete selected row
or
→ Select in the AutoCAD and hit delete
...
Stress Lines
Stress lines are the paths that indicate trajectory of internal forces, therefore these lines are idealized paths of material continuity.
...
Figure 3
→ Click Run Stress Line Generation button to automatically generate the stresslines as demonstrated in Figure 3.
→ Click Draw Stress Line as demonstrated in Figure 3 to draw stress lines between columns and/or shearwall corner zones manually.
→ Click Show Design Strip Results and select a direction to overlay the CSI SAFE design strip results as illustrated in Figure 4.
...
Figure 4
→ Click Refine Stress Line and select a direction.
Then AEC | BOLT Building Design Suite will suggest to user the stresslines which can be deleted as demonstrated in Figure 5.
...
Figure 5
User can select more stress lines in addition to selected ones.
→ Hit delete to delete selected stress lines then update the project.
→ Hold shift and click on the stress line to unselect.