| 1 |  🖱️ Click three-dots icon on Cross Sections cell and Edit.
|  Image Removed Image Added
|
| 2 | 🖱️ Click the three-dots icon on the Cross Section Location cell, and then set Abut1. |  Image Removed Image Removed Image Added
|
| 3 | As a result of these operations, an issue will appear on the OpenBrIM screen. This does not necessarily mean that any operation was done incorrectly. The issue will be resolved when the Cross Section, Girders and Material are set in the next step. |  |
| 4 | | Insert excerpt |
|---|
| _Quick Tips |
|---|
| _Quick Tips |
|---|
| name | Issue |
|---|
| nopanel | true |
|---|
|
|
| 5 | 🖱️ Keep the Offset from Support Line as default.
🖱️ Click the three-dots icon on the Cross Section cell, and then set DCS1. |  |
| 6 | 🖱️ Keep the Skew Angle as default.
🖱️ Click the three-dots icon on the Variation w/Next Segment cell, and then set Linear. |  |
| 7 | 🖱️ Move to the second row. 🖱️ Click the three-dots icon on the Cross Section Location cell, and then set Abut4. |  |
| 8 | 🖱️ Click three-dots on the first cell of the Girders and pick the girders G1, G2, G3, G4 |  Image Removed Image Removed Image Removed Image Added Image Added Image Added
|
| 9 | 🖱️ Keep the Taper , Continuous at Start and Continuous at End as default. |  Image Removed Image Added
|
| 10 | 🖱️ Click the three-dots icon on the Material cell, and then select Fc_4ksi4ksiforDeck. If you have reached this stage and you don't have a material to select, and if you want to use the Import Button, you can refer to the Quick Tip. |  Image Removed Image Removed Image Removed Image Added Image Added Image Added
|
| 11 | | Insert excerpt |
|---|
| _Quick Tips |
|---|
| _Quick Tips |
|---|
| name | ImportMaterial |
|---|
| nopanel | true |
|---|
|
|
| 12 | 🖱️ Click three-dots icon on Deck Reinforcement Data cell and Edit. |  Image Removed Image Added
|
| 13 | 🖱️Enter the Start Station as 0. |  |
| 14 | 🖱️Enter the End Station as 530. |  |
| 15 | 🖱️ Click the three-dots icon on the Deck Rebar Material cell, and then set A615_60. |  |
| 16 | 🖱️Enter the Long. Deck Rebar Spacing (Top Layer) and Long. Deck Rebar Spacing (Bottom Layer) as 5. |  |
| 17 | 🖱️ Click the three-dots icon on the Long. Deck Rebar (Top Layer) cell, and then set ASTMA615No8. |  |
| 18 | 🖱️ Click the three-dots icon on the Long. Deck Rebar (Bottom Layer) cell, and then set ASTMA615No6. |  |
| 19 | 🖱️ Keep the Clear Cover(Top) as default. |  |
| 20 | 🖱️Enter the Clear Cover(Bottom) as 3. |  |
| 21 | 🖱️ Keep the Concrete creep adjustment factor as default. |  |
| 22 | Keep the Curve Refinement 🖱️ Keep FEA and 3D Settings tabs parameters as default. |  Image Removed Image Added Image Added
|
| 23 | When the steps are completed, the shared screenshot displayed in the adjacent cell should be visible in the 3D view of OpenBrIM. |  |
| 24 | Proceed to the next step to verify the model. |