Content Comparison

Excerpt

name	Object Group

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup0
nopanel	true

This object allows you to group the objects found in the project. You can activate or deactivate the objects in each group you create in the project.

Pick Objects: The objects to be grouped can be picked one by one. However, it is easier to select all group objects by picking the main object first, and then selecting the reference objects associated with the main objects using 'Select References'.

Select Objects: Objects that cannot be picked, such as the wind load object which is not visible on the project screen, are selected using 'Select Object'.

Active: According to the 'Activation/Deactivation Impact', active objects' 3D geometries, finite models, and design reports can be enabled within the group, while those of inactive objects are not displayed in the project.

Activation/Deactivation Impact: The selection determines whether the object group affects the FEA model and/or Design reports.

FEA and Design Reset : This option affects both the FE models of the objects and their design reports. When the object is deactivated, the FE models of the selected objects are not created during the analysis process, and the design reports of the selected objects are not included in the design process.
Design Reset : This selection affects only the design reports of the objects. When the object is deactivated, the design reports of the selected objects during the design process are not included in the design process and become deactivated.

Note
To better understand the options for 'FEA and Design Reset' and 'Design Reset', follow the steps below.

1) FEA and Design Reset

1

Log in to your account and locate the 'Project' option in the top right corner.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allinoneworkflow2
nopanel	true

2

Click on 'Project' and then select 'NEW' from the top left corner of the screen.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allinoneworkflow1
nopanel	true

3

Under the 'Example Project' section, click on 'New Project' specifically located within the 'Precast I-Girder Training Example'.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allinoneworkflow9
nopanel	true

4

Provide a name for your project and proceed to open the example project.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allinoneworkflow10
nopanel	true

5

Panel

panelIconId	231b
panelIcon	:hourglass:
panelIconText	⌛
bgColor	#FFFAE6

Please note that the initial download process for the library components take approximately 2 minutes and 30 seconds to complete. The reopening of the same project will experience a notable increase in speed, primarily due to the caching of OpenBrIM library objects within your browser. The loading of library objects during this process generally takes less than 2-3 seconds

6

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allinoneworkflow11
nopanel	true

7

Click on the 'Data' button below.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allworkflow13
nopanel	true

8

The window that opens below shows the workflow tree on the left and the spreadsheet of the selected object on the right.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allworkflow14
nopanel	true

9

Scroll down in the workflow and click on the "Object Group" within the "Organization" group.

Insert excerpt

	_AllinonebridgeworkflowSS
	_AllinonebridgeworkflowSS
name	allworkflow15
nopanel	true

10

Name the group you are determining.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup1
nopanel	true

11

Click on three points by clicking on 'Pick Objects' input, then select 'Pick'.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup2
nopanel	true

12

Pick the 'Abut1' and 'Pier1' support lines on the project screen for UnitSpan1.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup3
nopanel	true

13

Panel

panelIconId	e42e3814-f644-4249-b705-23f6880c02b8
panelIcon	:iconinfo:
panelIconText	:iconinfo:
bgColor	#DEEBFF

Selecting all objects in the span can be difficult. Instead, it is easier to select support lines and then select the reference objects using 'Select References'.

14

Click on 'Select References' by clicking on three points.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup4
nopanel	true

15

In the opened 'Select Referencing Objects' screen, all reference objects related to the selected 2 support lines are listed.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup5
nopanel	true

16

When you click on any object, all reference objects of the clicked object are selected on the screen.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup6
nopanel	true

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup13
nopanel	true

17

Click 'Abut1' and 'Pier1' to select all their references. Then, remove the selection of 7 insertion points belonging to the second span (IP11, IP12, IP13, IP14, IP15, IP16, IP17).

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup7
nopanel	true

18

Panel

panelIconId	e42e3814-f644-4249-b705-23f6880c02b8
panelIcon	:iconinfo:
panelIconText	:iconinfo:
bgColor	#DEEBFF

Now all selected objects belong to Span 1.

19

Click on the 'Select' button at the bottom right of the 'Select Referencing Objects' screen to select the chosen objects.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup8
nopanel	true

20

Panel

panelIconId	e42e3814-f644-4249-b705-23f6880c02b8
panelIcon	:iconinfo:
panelIconText	:iconinfo:
bgColor	#DEEBFF

Now you can see all the selected objects listed under the 'Pick Objects' input.

21

When you click on the 'View All' button on the left side of the screen, you can see the created 'Object Group' objects here.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup9
nopanel	true

22

You can ensure control by viewing the created 'Object Group' objects.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup10
nopanel	true

23

Panel

panelIconId	e42e3814-f644-4249-b705-23f6880c02b8
panelIcon	:iconinfo:
panelIconText	:iconinfo:
bgColor	#DEEBFF

Similar steps are followed to create 'Object Groups' for Span-2 and Span-3.

24

Let's deactivate SpanUnit1 and activate only the objects in Span-2 and Span-3.

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup11
nopanel	true

25

Only the 3D and finite models of active objects are visible. Additionally, the design reports remaining in the deactivated section will also be deactivated. (This situation can be adjusted with the 'Activation/Deactivation Impact' input.)

Insert excerpt

	_ObjectGroupSS
	_ObjectGroupSS
name	objectGroup12
nopanel	true

2) Design Reset

1

Infopanel

panelIconId	e42e3814-f644-4249-b705-23f6880c02b8
panelIcon	:iconinfo:
panelIconText	:iconinfo:
bgColor	#DEEBFF

Do the steps of 'FEA and Design Reset' up to step 1423.

2

Set the "Activation/Deactivation Impact" input of the "Object Group" to "Design Reset".

Then deactivate 'UnitSpan1' and 'UnitSpan2'.

3

Panel

panelIconId	e42e3814-f644-4249-b705-23f6880c02b8
panelIcon	:iconinfo:
panelIconText	:iconinfo:
bgColor	#DEEBFF

Under the Substructure Code Check, there are three Concrete Pier Cap Code Checks available: EndBent1, PierCap1, and PierCap2. Since we have only activated 'Design Reset' for UnitSpan3, only the Code Check for PierCap2 among these objects will be included in the design stage.

Version	Old Version 19	New Version 20
Changes made by	Omer Faruk Ozkan	Omer Faruk Ozkan
Saved on	Mar 15, 2024	Mar 15, 2024

Versions Compared

Key

1) FEA and Design Reset

2) Design Reset