Content Comparison

Go to Foundation in the tree view. Enter Elevation as -5 feet. It will return to the Foundation step after completed Stories step.

Go to Stories in the tree view. Click Add button and add 3 floors. Enter 12-24-36 feet at the elevation of floors.

Choose 1st floor for all of them as a similar story. Place the 1st floor a drawing file.

Click Add button again.

"Enter a story no between 0 and 3 to define the story insertion point?"
Enter the value 3 in the question. This value entered is the Stories number. New stories to be added will be placed on top of this Stories.as 3

"How many stories do you want to create?" Enter the value 1 in the question.

Here we check the operation of the add floor button.

Copy all the data from the top line to the new added floorstory, manually enter the elevation value of as 48 feet and change New Stories' name to Roof.

Go to the 1st floor in Stories. Check that if the values of the properties values are correct.

Call Display the Drawing file added to of the 1st floor to in the CAD view by using overlay button.

Go to the Slab below 1st floor Slab. Draw Slab Edge on CAD view. Enter data as in the screen shoot.

Click the Refresh Parametric Model button to update the model and check the 3D view.

Draw Slab Piece on CAD view. Enter data as in the figure. Click Refresh Parametric Model Button.

Click the Design Strip button. Draw a line for design strip.

Click yes for the question "Do you want to create same design strip definition for all stories?".

Go to Openings below 1st floor Openings. Draw the openings.

Have to draw Draw 1 Rectangular, 1 circleCircle, 1 Arbitrary Openings according to CAD viewOpening as seen in below view. Click Refresh Parametric Model Button.

Go to Shearwall below 1st floor Shearwall from treeview. Draw Shearwall by using Shearwall button. Set material value. Click Refresh Parametric Model Button.

Check if the hold point can be changed.

Go to the Analytical definition tab. Draw an Analytical wall on CAD view.

Make sure that a break point is formed on the horizontal wall.

Click the elevation views to see the horizontal view of the Shearwall.

Click on the wall opening. Have to draw rectangular, circular and arbitrary opening on Shearwall.

Go to the Column below 1st floor and draw rectangular column by using rectangular column button. Enter 30° degree orientation angle.

Draw a circular column by using circular column button. Enter the bottom offset X=10 inch and Y=20 inch

Click the Arbitrary Column button, draw an Arbitrary column. Change the Hold point of column C2. Enter an orientation angle of 45° and 60° degrees in C1 and C2 columns

You can enter remaining cells based on the figure.

Click the Show Tributary button. Check if tributary area of each column is the same or similar to the figure given.

Go to Beam below 1st floor. Click draw beam button and draw the beam between 2 arbitrary columns.

Enter the Material class="Conc 4000psi" and Depth="24 inch" values into the cell.

Click the Beam Type cell to check the drawn beam type.
Check have "Gravity" and "Lateral" options.
Select the "Gravity" button

Go to the analytical line and draw the analytical line. Enter the width and depth values. Manually enter the break point right in the middle on beam

Click the Show Tributary button. Check the tributary area of the beam.

Go to Load below under 1st floor from tree view. Click area button and draw the area in the CAD view
Click line button and draw the line load in the CAD view.
Click point button create point load in the CAD view

Have to select Load case for these these loads according to figure

After all the values are entered in the cells, click the Refresh Load Distribution Factors button. Make sure the Geometric Distribution To column % value is 100%.

Right click on LG1 area load and click duplicate from the window.
You will get a see the duplicated 2nd Load drawn over the LG 1 that uses same area.
Have to set Set Load Case according to the figure below

Go back to the 1st floor. Click the Update similar stories button. Select all checkbox on the left side of the table. Select the 2nd floor checkbox on the right.

Click the Update similar stories button.

As seen in the figure, number of objects selected is written left side under Update Similar Stories button.

Go to the 3rd floor and click Copy From button.

Select all the checkbox in the Select objects to copy section. Select 1st floor in Select a source story. Click the copy all button.

Go to the Roof and click the Copy From. Select object to copy tab. Select Slabs, Openings, Columns objects.

Select 1st floor as the source story and click the Select Graphically button. Select the objects from the drawing and click enter.

Check if only selected objects are present in the overlay drawing.

Go to the 1st Floor click the Select Update Similar Stories tab. Select Shearwall, Load and beam objects at checkbox. Select Roof as "Select Stories to Paste" and click the Select in CAD button.

Select the objects from the drawing and click enter.
Check if there are only selected objects in the overlay drawing.